Strain compatibility design method for reinforced earth walls

Ilan Juran, Chao L. Chen

Research output: Contribution to journalArticle

Abstract

The methods currently used for the design of reinforced earth walls with quasi-inextensible metallic reinforcements are essentially based either upon the limit stress analysis concept or empirical relationships derived from observations on full scale structures. The development of an adequate working stress design method for these structures requires a fundamental understanding of the reinforcement effect on the load-deformation behavior of the soil and a rational, yet relatively simple, load transfer model to simulate the soil-reinforcement interaction. Furthermore, the response of the composite-reinforced soil material to loading is highly dependent upon the initial state of stress and strain in the soil, and therefore the construction process and soil compaction can significantly affect the structure behavior under the expected working loads. A strain compatibility design approach which is fundamentally based on the analogy between the plane strain shear mechanism which develops along a potential failure surface in the actual structure and the response of the reinforced soil material to direct shearing is presented. The soil-reinforcement load transfer model used in this analysis allows for the evaluation of the effect of soil dilatancy and extensibility of the reinforcement on the generated tension forces and on the probable location of the potential failure surface. In order to verify the model/design assumptions, numerical simulations of the construction process are compared with at-failure observations on reduced scale laboratory model walls as well as with tension forces measured in reinforcements of both reduced scale model walls and full scale structures.

Original languageEnglish (US)
Pages (from-to)435-456
Number of pages22
JournalJournal of Geotechnical Engineering
Volume115
Issue number4
DOIs
StatePublished - 1989

Fingerprint

reinforced earth
design method
Earth (planet)
reinforcement
Soils
Reinforcement
soil reinforcement
soil
stress analysis
dilatancy
plane strain
Shear strain
Stress analysis
Shearing
Loads (forces)
Compaction
simulation

ASJC Scopus subject areas

  • Geotechnical Engineering and Engineering Geology
  • Engineering(all)

Cite this

Strain compatibility design method for reinforced earth walls. / Juran, Ilan; Chen, Chao L.

In: Journal of Geotechnical Engineering, Vol. 115, No. 4, 1989, p. 435-456.

Research output: Contribution to journalArticle

@article{502578fa03634b94a410db1add68fe97,
title = "Strain compatibility design method for reinforced earth walls",
abstract = "The methods currently used for the design of reinforced earth walls with quasi-inextensible metallic reinforcements are essentially based either upon the limit stress analysis concept or empirical relationships derived from observations on full scale structures. The development of an adequate working stress design method for these structures requires a fundamental understanding of the reinforcement effect on the load-deformation behavior of the soil and a rational, yet relatively simple, load transfer model to simulate the soil-reinforcement interaction. Furthermore, the response of the composite-reinforced soil material to loading is highly dependent upon the initial state of stress and strain in the soil, and therefore the construction process and soil compaction can significantly affect the structure behavior under the expected working loads. A strain compatibility design approach which is fundamentally based on the analogy between the plane strain shear mechanism which develops along a potential failure surface in the actual structure and the response of the reinforced soil material to direct shearing is presented. The soil-reinforcement load transfer model used in this analysis allows for the evaluation of the effect of soil dilatancy and extensibility of the reinforcement on the generated tension forces and on the probable location of the potential failure surface. In order to verify the model/design assumptions, numerical simulations of the construction process are compared with at-failure observations on reduced scale laboratory model walls as well as with tension forces measured in reinforcements of both reduced scale model walls and full scale structures.",
author = "Ilan Juran and Chen, {Chao L.}",
year = "1989",
doi = "10.1061/(ASCE)0733-9410(1989)115:4(435)",
language = "English (US)",
volume = "115",
pages = "435--456",
journal = "Journal of Geotechnical and Geoenvironmental Engineering - ASCE",
issn = "1090-0241",
publisher = "American Society of Civil Engineers (ASCE)",
number = "4",

}

TY - JOUR

T1 - Strain compatibility design method for reinforced earth walls

AU - Juran, Ilan

AU - Chen, Chao L.

PY - 1989

Y1 - 1989

N2 - The methods currently used for the design of reinforced earth walls with quasi-inextensible metallic reinforcements are essentially based either upon the limit stress analysis concept or empirical relationships derived from observations on full scale structures. The development of an adequate working stress design method for these structures requires a fundamental understanding of the reinforcement effect on the load-deformation behavior of the soil and a rational, yet relatively simple, load transfer model to simulate the soil-reinforcement interaction. Furthermore, the response of the composite-reinforced soil material to loading is highly dependent upon the initial state of stress and strain in the soil, and therefore the construction process and soil compaction can significantly affect the structure behavior under the expected working loads. A strain compatibility design approach which is fundamentally based on the analogy between the plane strain shear mechanism which develops along a potential failure surface in the actual structure and the response of the reinforced soil material to direct shearing is presented. The soil-reinforcement load transfer model used in this analysis allows for the evaluation of the effect of soil dilatancy and extensibility of the reinforcement on the generated tension forces and on the probable location of the potential failure surface. In order to verify the model/design assumptions, numerical simulations of the construction process are compared with at-failure observations on reduced scale laboratory model walls as well as with tension forces measured in reinforcements of both reduced scale model walls and full scale structures.

AB - The methods currently used for the design of reinforced earth walls with quasi-inextensible metallic reinforcements are essentially based either upon the limit stress analysis concept or empirical relationships derived from observations on full scale structures. The development of an adequate working stress design method for these structures requires a fundamental understanding of the reinforcement effect on the load-deformation behavior of the soil and a rational, yet relatively simple, load transfer model to simulate the soil-reinforcement interaction. Furthermore, the response of the composite-reinforced soil material to loading is highly dependent upon the initial state of stress and strain in the soil, and therefore the construction process and soil compaction can significantly affect the structure behavior under the expected working loads. A strain compatibility design approach which is fundamentally based on the analogy between the plane strain shear mechanism which develops along a potential failure surface in the actual structure and the response of the reinforced soil material to direct shearing is presented. The soil-reinforcement load transfer model used in this analysis allows for the evaluation of the effect of soil dilatancy and extensibility of the reinforcement on the generated tension forces and on the probable location of the potential failure surface. In order to verify the model/design assumptions, numerical simulations of the construction process are compared with at-failure observations on reduced scale laboratory model walls as well as with tension forces measured in reinforcements of both reduced scale model walls and full scale structures.

UR - http://www.scopus.com/inward/record.url?scp=0024649257&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=0024649257&partnerID=8YFLogxK

U2 - 10.1061/(ASCE)0733-9410(1989)115:4(435)

DO - 10.1061/(ASCE)0733-9410(1989)115:4(435)

M3 - Article

VL - 115

SP - 435

EP - 456

JO - Journal of Geotechnical and Geoenvironmental Engineering - ASCE

JF - Journal of Geotechnical and Geoenvironmental Engineering - ASCE

SN - 1090-0241

IS - 4

ER -