Investigation of UF membranes fouling and potentials as pre-treatment step in desalination and surface water applications

Saif Al Aani, Chris J. Wright, Nidal Hilal

Research output: Contribution to journalArticle

Abstract

The surface fouling of UF membranes used upstream as pre-treatment stage is critical for the long-term stability of the subsequent treatment stage (NF/RO membranes). In this paper, an attempt was made to probe and compare the potential of versatile UF membranes structures in terms of flux decline and selectivity, for more convenient pretreatment membranes selection. The role of polyethersulfone (PES) host polymer concentration, on the morphology and surface characteristics of asymmetric flat sheet ultrafiltration (UF) membranes, has been comprehensively investigated. Distinctly, as the casting solution viscosity decrease, a higher pore size, pore size distribution and pure water flux was observed along with lower mechanical properties and wider cross-section morphologies. However, this impact was trivial on water contact angle, surface roughness parameters and charge negativity of the membrane. To further assess the potential performance of the hand-made fabricated membranes, they were systematically evaluated against three organic model foulants with dissimilar origins; humic acid (HA) – as natural organic matters (NOM), sodium alginate (NaAlg) – as polysaccharide, and bovine serum albumin (BSA) – as protein, under different initial feed concentration and pH chemistry. A disparate fouling behavior was observed depending on the membrane characteristics and the organic model foulant used. Depending on the UF membrane cut-off used, lower MWCO membranes, PES22 (6 kDa) and PES20 (10 kDa) exhibited a negligible relative flux decline while extremely low relative flux patterns were observed in the filtration with the 100 kDa membrane (PES16), as a result of one or more pore blocking mechanisms observed.

Original languageEnglish (US)
Pages (from-to)115-127
Number of pages13
JournalDesalination
Volume432
DOIs
StatePublished - Apr 15 2018

Fingerprint

Membrane fouling
Ultrafiltration
Desalination
ultrafiltration
Surface waters
fouling
desalination
membrane
Membranes
surface water
Fluxes
Fouling
Pore size
Humic Substances
Sodium alginate
Membrane structures
Water
Polysaccharides
alginate
Bovine Serum Albumin

Keywords

  • Bovine serum albumin
  • Desalination
  • Fouling
  • Humic acid
  • PES concentration
  • Polyethersulfone membrane
  • Pre-treatment
  • Sodium alginate

ASJC Scopus subject areas

  • Chemistry(all)
  • Chemical Engineering(all)
  • Materials Science(all)
  • Water Science and Technology
  • Mechanical Engineering

Cite this

Investigation of UF membranes fouling and potentials as pre-treatment step in desalination and surface water applications. / Al Aani, Saif; Wright, Chris J.; Hilal, Nidal.

In: Desalination, Vol. 432, 15.04.2018, p. 115-127.

Research output: Contribution to journalArticle

@article{b9b880dae5a2441ba73f18ae34a28618,
title = "Investigation of UF membranes fouling and potentials as pre-treatment step in desalination and surface water applications",
abstract = "The surface fouling of UF membranes used upstream as pre-treatment stage is critical for the long-term stability of the subsequent treatment stage (NF/RO membranes). In this paper, an attempt was made to probe and compare the potential of versatile UF membranes structures in terms of flux decline and selectivity, for more convenient pretreatment membranes selection. The role of polyethersulfone (PES) host polymer concentration, on the morphology and surface characteristics of asymmetric flat sheet ultrafiltration (UF) membranes, has been comprehensively investigated. Distinctly, as the casting solution viscosity decrease, a higher pore size, pore size distribution and pure water flux was observed along with lower mechanical properties and wider cross-section morphologies. However, this impact was trivial on water contact angle, surface roughness parameters and charge negativity of the membrane. To further assess the potential performance of the hand-made fabricated membranes, they were systematically evaluated against three organic model foulants with dissimilar origins; humic acid (HA) – as natural organic matters (NOM), sodium alginate (NaAlg) – as polysaccharide, and bovine serum albumin (BSA) – as protein, under different initial feed concentration and pH chemistry. A disparate fouling behavior was observed depending on the membrane characteristics and the organic model foulant used. Depending on the UF membrane cut-off used, lower MWCO membranes, PES22 (6 kDa) and PES20 (10 kDa) exhibited a negligible relative flux decline while extremely low relative flux patterns were observed in the filtration with the 100 kDa membrane (PES16), as a result of one or more pore blocking mechanisms observed.",
keywords = "Bovine serum albumin, Desalination, Fouling, Humic acid, PES concentration, Polyethersulfone membrane, Pre-treatment, Sodium alginate",
author = "{Al Aani}, Saif and Wright, {Chris J.} and Nidal Hilal",
year = "2018",
month = "4",
day = "15",
doi = "10.1016/j.desal.2018.01.017",
language = "English (US)",
volume = "432",
pages = "115--127",
journal = "Desalination",
issn = "0011-9164",
publisher = "Elsevier",

}

TY - JOUR

T1 - Investigation of UF membranes fouling and potentials as pre-treatment step in desalination and surface water applications

AU - Al Aani, Saif

AU - Wright, Chris J.

AU - Hilal, Nidal

PY - 2018/4/15

Y1 - 2018/4/15

N2 - The surface fouling of UF membranes used upstream as pre-treatment stage is critical for the long-term stability of the subsequent treatment stage (NF/RO membranes). In this paper, an attempt was made to probe and compare the potential of versatile UF membranes structures in terms of flux decline and selectivity, for more convenient pretreatment membranes selection. The role of polyethersulfone (PES) host polymer concentration, on the morphology and surface characteristics of asymmetric flat sheet ultrafiltration (UF) membranes, has been comprehensively investigated. Distinctly, as the casting solution viscosity decrease, a higher pore size, pore size distribution and pure water flux was observed along with lower mechanical properties and wider cross-section morphologies. However, this impact was trivial on water contact angle, surface roughness parameters and charge negativity of the membrane. To further assess the potential performance of the hand-made fabricated membranes, they were systematically evaluated against three organic model foulants with dissimilar origins; humic acid (HA) – as natural organic matters (NOM), sodium alginate (NaAlg) – as polysaccharide, and bovine serum albumin (BSA) – as protein, under different initial feed concentration and pH chemistry. A disparate fouling behavior was observed depending on the membrane characteristics and the organic model foulant used. Depending on the UF membrane cut-off used, lower MWCO membranes, PES22 (6 kDa) and PES20 (10 kDa) exhibited a negligible relative flux decline while extremely low relative flux patterns were observed in the filtration with the 100 kDa membrane (PES16), as a result of one or more pore blocking mechanisms observed.

AB - The surface fouling of UF membranes used upstream as pre-treatment stage is critical for the long-term stability of the subsequent treatment stage (NF/RO membranes). In this paper, an attempt was made to probe and compare the potential of versatile UF membranes structures in terms of flux decline and selectivity, for more convenient pretreatment membranes selection. The role of polyethersulfone (PES) host polymer concentration, on the morphology and surface characteristics of asymmetric flat sheet ultrafiltration (UF) membranes, has been comprehensively investigated. Distinctly, as the casting solution viscosity decrease, a higher pore size, pore size distribution and pure water flux was observed along with lower mechanical properties and wider cross-section morphologies. However, this impact was trivial on water contact angle, surface roughness parameters and charge negativity of the membrane. To further assess the potential performance of the hand-made fabricated membranes, they were systematically evaluated against three organic model foulants with dissimilar origins; humic acid (HA) – as natural organic matters (NOM), sodium alginate (NaAlg) – as polysaccharide, and bovine serum albumin (BSA) – as protein, under different initial feed concentration and pH chemistry. A disparate fouling behavior was observed depending on the membrane characteristics and the organic model foulant used. Depending on the UF membrane cut-off used, lower MWCO membranes, PES22 (6 kDa) and PES20 (10 kDa) exhibited a negligible relative flux decline while extremely low relative flux patterns were observed in the filtration with the 100 kDa membrane (PES16), as a result of one or more pore blocking mechanisms observed.

KW - Bovine serum albumin

KW - Desalination

KW - Fouling

KW - Humic acid

KW - PES concentration

KW - Polyethersulfone membrane

KW - Pre-treatment

KW - Sodium alginate

UR - http://www.scopus.com/inward/record.url?scp=85044333093&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85044333093&partnerID=8YFLogxK

U2 - 10.1016/j.desal.2018.01.017

DO - 10.1016/j.desal.2018.01.017

M3 - Article

AN - SCOPUS:85044333093

VL - 432

SP - 115

EP - 127

JO - Desalination

JF - Desalination

SN - 0011-9164

ER -